Erection Anchor

Erection Anchor

Flat anchor

GME Flat Anchor is an alternative to the plate anchor.

The main use is in elements with a concrete strength at lifting in excess of 25N/mm²

The Plate-Lift Flat Foot Anchor, also called The Lift Spread Foot Anchor, is a versatile anchor that can be used to back-strip and transport thin panels. This anchor may also be used to erect the panels. Its main application is thin-walled concrete elements, being lifted from horizontal to a vertical position. The special shape of the anchor head prevents the concrete from cracking. This kind of anchor is typically used with additional reinforcement, which is required for tilting and turning operations. The anchor's safe working load may be increased by adding four 18" lengths of #4 rebar as shown in the sketch. These anchors are commonly used in slabs/panels due to their capacities and low cost. Available in plain or hot-dipped galvanized finish.

Load   Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		H	W	T	L
2.5	1.4	GME2005014065	65	30	6	70
2.5	2.5	GME2005025075	75	30	10	94
5.0	3.0	GME2005030090	90	40	10	100
5.0	4.0	GME2005040110	no	40	12	100
5.0	5.0	GME2005050125	125	40	15	105
10.0	5.3	GME2005053150	320	60	12	120
10.0	7.5	GME2005075170	170	60	16	120
10.0	10.0	GME2005100200	200	60	20	120
26.0	12.5	GME2005125220	220	80	20	200
26.0	17.0	GME2005170270	270	80	25	200
26.0	22.0	GME2005220310	310	120	30	200

Other different Lengths and load capacity are available upon request.

The safety Factor is 3:1.

Stainless Steel 304(A2)/316(A4) are available upon request Surface: Black(B)/Zinc Plated(Z.P)/Hot Dipped Galvanized(H.D.G) are available.

Two-Hole Anchor

·Used for stripping panels from tilt tables and tripping panels

·Also appropriate for high tension loads that cannot be held with other anchors or for panels constructed of lightweight concrete

·Safe working loads up to 10 tons

·Based on a 3:1 safety factor

Load Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		L	W	T	D
2.5	1.4	GME2001014090	90	30	6	14
2.5	2	GME2001020090	90	30	8	14
2.5	2.5	GME2001025090	90	30	10	14
5	3	GME2001030120	120	40	10	18
5	4	GME2001040120	120	40	12	18
5	5	GME2001050120	120	40	15	18
10	5.3	GME2001053160	160	60	12	26
10	7.5	GME2001075160	160	60	16	26
10	10	GME2001100170	170	60	20	30
26	14	GME2001140240	240	80	20	35
26	17	GME2001170300	300	80	25	35
26	26	GME2001220300	300	120	30	65

Ring Lift Plate Anchor

· Used for face and back lifts of thin-walled units.

· Low profile with a wide, flat base for excellent

· anchorage

· Horizontal plate welded to the bottom gives

· creates high pull-out strength in stripping, handling, and erection applications.

· Based on a 4:1 safety factor

Load Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		H	W	f	e
2.5	1.4	GME2007014005	55	30	8	80
2.5	2.5	GME2007025080	80	30	8	80
5	5	GME2007050120	120	40	10	100
10	10	GME2007100160	160	60	12	140

Drop Forged Foot Anchor

GME Drop Forged Foot Anchor is a high-strength, hot-forged anchor.

·Used for stripping panels from tilt tables and tripping panels

·Also appropriate for high tension loads that cannot be held with other anchors or for panels constructed of lightweight concrete

·Safe working loads up to 10 tons

·Based on a 4:1 safety factor

Load   Group	Axial Load	Code	Dimensions (Inch)			Hole
Tons	LBS		L	W	T
2.5	3900	GME2102025321	3-1/2	1-1/4	3/8	1
2.5	4400	GME2102025400	4	1-1/4	3/8	1
2.5	4400	GME2102025421	4-1/2	1-1/4	3/8	2
2.5	4510	GME2102025521	5-1/2	1-1/4	3/8	2
2.5	5500	GME2102025634	6-3/4	1-1/4	3/8	2
5.0	4400	GME2102050312	3-1/2	1-1/2	5/8	1
5.0	6200	GME2102050412	4-1/2	1-1/2	5/8	2
5.0	8800	GME2102050512	5-1/2	1-1/2	5/8	2
5.0	11000	GME2102050912	9-1/2	1-1/2	5/8	2
10.0	6200	GME2102100434	4-3/4	2-1/2	3/4	1
10.0	8500	GME2102100512	5-1/2	2-1/2	3/4	1
10.0	12500	GME2102100-7	7	2-1/2	3/4	2
10.0	22000	GME2102100-10	10	2-1/2	3/4	2

Plate Lift Forged Erection Anchor

Forged Erection Anchor is specifically designed to provide greater lifting capacities for horizontal to vertical edge lifts. The anchors are forged to provide 20% greater safe working loads. The head of the anchor is designed with two protrusions or "ears" on the head of the anchor which provide protection against concrete spalling. These protrusions restrict the ring clutch rotation during lateral pulls. As a result, lateral forces are transmitted directly to the edge of the anchor instead of the concrete. The Anchors are available in plain or hot-dipped galvanized finishes.

Load Group	Axial Load	Code	Dimensions (Inch)
Tons	LBS		L	W	T
2.5	6000	GME2104-2.5	8	2	3/8
5.0	12000	GME2104-5.0	10-3/8	2-1/2	5/8
10.0	20000	GME2104-10.0	12-3/4	3-3/4	3/4

Fleet-Lift Drop Forged Erection Anchor with Shear Plate

GME Fleet-Lift Drop Forged Erection Anchor with Shear Plate eliminates the need for a shear bar.

Load Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		L	W	T
2.5	6	GME2105-2.5	8	2	3/8
5.0	12000	GME2105-5.0	10-3/8	2-1/2	5/8
10.0	20000	GME2105-10.0	12-3/4	3-3/4	3/4

Spread Anchor

The spread anchor is very versatile. It provides an efficient anchorage in both thin panels and slabs. For special applications, additional reinforcement can be combined with the spread anchor by utilizing the extra hole.

Load range 0.7t to 22.0t

Safety factor: 3:1

Load Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		L	W	T	d
2.5	1.4	GME20030I4110	110	30	6	14
2.5	1.4	GME2003014160	160	30	6	14
2.5	2	GME2003020130	130	30	8	14
2.5	2	GME2003020160	160	30	8	14
2.5	2	GME2003020210	210	30	8	14
2.5	2.5	GME2003025150	150	30	10	14
2.5	2.5	GME2003025200	200	30	10	14
2.5	2.5	GME2003025250	250	30	10	14
5	3	GME2003030160	160	40	10	18
5	3	GME2003030200	200	40	10	18
5	3	GME2003030280	280	40	10	18
5	4	GME2003040180	180	40	12	18
5	4	GME2003040240	240	40	12	18
5	4	GME2003040320	320	40	12	18
5	5	GME2003050180	180	40	15	18
5	5	GME2003050240	240	40	15	18
5	5	GME2003050400	400	40	15	18
10	5.3	GME2003053220	220	60	12	26
10	5.3	GME2003053260	260	60	12	26
10	5.3	GME2003053340	340	60	12	26
10	7.5	GME2003075260	260	60	16	26
10	7.5	GME2003075300	300	60	16	26
10	7.5	GME2003075420	420	60	16	26
10	10	GME2003100300	300	60	20	26
10	10	GME2003100370	370	60	20	26
26	10	GME2003100520	520	60	20	26
26	14	GME2003140370	370	80	20	35
26	14	GME2003140460	460	80	20	35
26	22	GME2003220500	500	80	25	35
26	22	GME2003220620	620	80	25	35

Unilateral Erection Anchor

GME Unilateral Erection Anchor is a similar Application as Erection Anchor.

In contrast to the erection anchor, a Unilateral erection anchor can only be subjected to load in one direction. Its shape makes it particularly suitable for thin components.

A semi-circular notch is provided for the fitting of the turning reinforcement.

Safety factor: 3:1

Load Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		L	W	T
2.5	1.4	GME2004014200	200	40	6
2.5	2.5	GME2004025230	230	40	10
5	4	GME2004040270	270	55	12
5	5	GME2004050290	290	55	16
10	7.5	GME2004075320	320	80	16
10	10	GME2004100390	390	80	20
26	12.5	GME2004125500	500	114	20
26	17	GME2004170500	500	114	25
26	22	GME2004220300	500	114	30

Sandwich Panel Anchor

GME Sandwich Panel Anchor is specially designed for use with precast sandwich panels.

Safety factor: 3:1

Load Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		L	W	T
2.5	2.5	GME2006025250	250	40	10
5	5	GME2006050300	300	60	16
10	7.5	GME2006075350	350	80	16
10	10	GME2006100350	350	80	20
26	17	GME2006170400	400	100	20

Erection anchor

Erection anchor The special-shaped anchor head means that the pitching/turning loads are taken by the anchor and not to the concrete. This helps prevent the ling of the concrete. The anchors are notched to assist with the placement of additional reinforcement required in the pitching/turning operation.

Load range 1.4t to 22.0t

Load Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		L	W	T
1.25	1.25	GME2002-1.25	120	30	6
2.5	1.4	GME2002014200	200	55	6
2.5	2.5	GME2002025230	230	55	10
5	4	GME2002040270	270	70	12
5	5	GME2002050290	290	70	16
10	7.5	GME2002075320	320	95	16
10	10	GME2002100390	390	95	20
26	12.5	GME2002125500	500	148	20
26	17	GME2002170500	500	148	25
26	22	GME2002220300	500	148	30

X-Foot Erection Anchor

For horizontal to vertical edge lifts and the shear rotation of thin-walled units.

· Specially designed head provides added protection against spalling

· For lifts applying shear and tension to the anchor

· Specially designed body allows for all reinforcement

· Available in 2T, 4T, or 8T capacities

· Based on a 4:1 safety factor Superior Design Two steel protrusions or "ears" on the head of the anchor provides added protection against spalling. These ears hug either side of the ring clutch, restricting its rotation during lateral pulls. As a result, lateral forces are transmitted directly to the edges of the anchor instead of the concrete.

The body of the Erection Anchor is shaped to allow full reinforcement for secure support.

ANCHOR  TONNAGE	CLUTCH ID	WIDTH (W)	LENGTH (L)	THICKNESS (T)	SWL4:1 SF TENSION  W/TENSION BAR	WEIGHT EACH	WORKING LOAD REINFORCED  2000 PSI CONCRETE TENSION	MIN. EDGE DISTANCE	WEIGHT EACH
tons	#	in.	in.	in.	lb	lb	lb	in.	lb
2T	2-2.5T	2	8	3/8	4.000	1.59	4.000	4-1/2	0.89
4T	4-5T	2-1/2	9-1/2	5/8	8,000	4.20	8,000	6	1.21
8T	8-10T	3-1/2	13-1/2	3/4	16,000	9.30	8,000	7	1.69

Ring Lift Erection Anchor with Shear Plate

Combines the reinforcing capabilities of the Ring Lift Anchor with the spall-free performance of an Erection Anchor

· The shear plate replaces the need for a shear bar making it easier to install

· Ideal for an "A" frame or tilt table or whenever the lift is not straight up

· For lifts that entail only anchor tension

· Shear capacity is less than the standard erection anchor due to the shorter length

· The anchor's head loads are equal to the standard erection anchor due to length

· Convex sides build better strength without adding material

· Available in 2T, 2.5T, 4T, 5T, 8T, 10T capacities

· Based on a 4:1 safety factor

Load   Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		L	W	T
2.5	2.0	GME2010020200	200	55	10
5.0	4.0	GME2010040270	270	70	16
10.0	6.0	GME2010060325	325	95	16
10.0	8.0	GME2010080325	325	95	20

Plate-Lift Erection Anchor

Plate-Lift Erection Anchors are specifically designed for horizontal to vertical edge lifts and handling of thin-walled precast concrete elements. Two steel protrusions or "ears" on the head of the anchor provide protection against concrete spalling. These protrusions restrict the ring clutch rotation during lateral pulls. As a result, lateral forces are transmitted directly to the edge of the anchor instead of the concrete.

The body of the Erection Anchor is shaped to allow full reinforcement for secure support and spall-free rotation. Erection Anchors are available plain or hot-dipped galvanized.

Safe Working Load (Tons)	A	B	C	D	E	F	G	H	J	X
2	2"	8''	3/8，，	1-13/16" 2-3/8"		3-3/8-	5/8''	1''	1/2''	3/8"
4	2-1/2"	10-7/16'' 5/8"		2-1/2"	3-3/16"	4-7/16"	3/4''	1-1/4"	3/4''	7/16''
6	3-3/4"	13-1/4"	5/8"	3-1/8"	4"	5-3/4"	1''	1-3/4"	3/4"	5/8"
8	3-3/4"	13-1/4"	3/4"	3-1/8"	4"	5-3/4-	1''	1-3/4"	3/4"	5/8"

Plate-Lift Erection Anchor with Shear Plate

Plate-Lift Erection Anchor with Shear Plate is designed specifically forged tilting precast concrete elements from the horizontal to a vertical position. An integral shear plate eliminates any possibility of forgetting to install a required shear bar.

As on other Plate-Lift Erection Anchors, two steel protrusions or "ears' at the head of the anchor provide protection against concrete spalling. These "ears" restrict the ring clutch rotation during lateral pulls. As a result, lateral forces are transmitted directly to the edge of the anchor instead of the concrete.

The body of the erection anchor is shaped to allow full reinforcement for secure support and spall-free rotation.

Erection Anchors are available plain or hot-dipped galvanized.

Load Group	Axial Load	Code	Dimensions (mm)
Tons	Tons		L	W	T
2.5	2.0	GME2010020200SP	200	55	10
4.0	GME2010040270SP	GME2010040270SP	70	16	16
10.0	6.0	GME2010060325SP	325	95	16
8.0	GME2010080325SP	GME2010080325SP	95	20	20

Plate-Lift Erection Anchor with 45° Head with Shear Plate

Plate-Lift Erection Anchor with 45° Head with Shear Plate is designed for use when the lifting edge is beveled at a 45° angle. The factory-installed shear plate eliminates the need for any additional shear reinforcement. Erection Anchors are available plain, or hot-dipped galvanized.

P-92-AH Fleet-Lift Erection Anchor (ton x length)	Product Code	Precast Concrete Panel Thickness	Shear Safe  Working Load for Shear	Tension Safe  Working Load Anchor Only	Tension Safe  Working Load with Tension Bar	A	B	C	D
2-ton x  8-1/2" long	FL452	5" Min.	1,750 lbs.	2,650 lbs.	2,650 lbs.	2"	8-1/2"	3/8''	3-1/2''
2-ton x 8-1/2" long	FL452	6"	2,150 lbs.	3.850 lbs.	3,850 lbs.	2"	8-1/2"	3/8''	3-1/2''
4-ton x 11'' long	FL454	6" Min.	2.400 lbs.	5,200 lbs.	5,200 lbs.	2-1/2''	11''	5/8"	4"
4-ton x 11" long	FL454	8''	3,500 lbs.	6,200 lbs.	6,200 lbs.	2-1/2''	11'	5/8"	4"
8-ton x 13-3/4" long	FL458	8" Min.	3,500 lbs.	7,500 lbs.	7,500 lbs.	3-3/4''	13-3/4''	3/4''	5-3/8''

Fleet-Lift Sandwich Panel Erection Anchor

The Fleet-Lift Sandwich Panel Erection Anchor is designed to erect precast, insulated sandwich panels with a minimum loss of insulation and designed for use in 2"×2"×2",3"×2"×3" and 2"×2"×4" thick insulated sandwich panels. The design of the anchor allows it to distribute anchor loads evenly to both concrete. This is accomplished by the use of two specially bent rebars per sandwich panel anchor. The sandwich panel erection anchor, with its unique anchor head shape, in combination with the two bent rebars, transfers both the anchor's shear and tension loads evenly into each of the concrete. Place one bent rebar through the anchor's top hole and the second rebar through the anchor's bottom hole. The rebar extends from the anchor into the top and bottom of the concrete. The two specially bent rebars must be used with the sandwich panel erection anchor to achieve the safe working loads shown.

Fleet-Lift Sandwich Panel Erection Anchor with Shear Plate is similar in design and action to without the shear plate, above, except it is smaller overall and has a built-in shear plate The shear plate improves shear capacity when used in the 2" thick.

Load Group	Axial Load	Code	Dimensions (mm)
2.5	2.5	GME2008025100	100	50	10
5	5	GME2008050180	180	63.5	16
10	10	GME2008100180	180	90	20
10	10	GME2008100340	340	90	20
2.5	2.5	GME2008025100SP	100	50	10
5	5	GME2008050180SP	180	63.5	16
10	10	GME2008100180SP	180	90	20
10	10	GME2008100340SP	340	90	20

Butterfly type Sandwich Panel Erection Anchor with Shear Plate

GME Butterfly type Sandwich Panel Erection Anchor is designed to erect precast, insulated sandwich panels with a min. loss of insulation. The Anchor uses standard Recess Former and Ring Clutch. Forged Wing Sandwich panels are available. The Anchor with Shear Plate has a similar function in design but improves shear capacity.

·Based on a 3:1 safety factor

Plate-Lift H-Anchor

The Plate-Lift H-Anchor is unique in design simplicity. It offers exceptional strength for lifting and handling precast elements, yet can be used in panels as thin as 3". The anchor can be easily preset in the form or "wet set" after the concrete has been poured.

The H-Anchor is the strongest and most economical precast lifting anchor available for back-stripping. H-Anchors are available in plain and hot-dipped galvanized finish.

Product  Code	A	B	C	D	Minimum  Slab  Thickness	Weight Each
FL523	1.25''	2.30''	0.35''	0.56"	3"	0.28 lbs.
FL524	1.25''	3.30''	0.38''	1.44''	4"	0.36 lbs.

Plate-Lift L-Anchor

Plate-Lift L-Anchor is a very efficient anchor. This anchor is used for both stripping and erection carrying tension and/or shear loads(except for edge shear in thin panels). The L-Anchor produces exceptionally high pullout strength for its size, due to its foot design. The L-Anchor can be placed on the face, back, or thicker panel edge allowing for back stripping and their rotation from horizontal to vertical. The anchor is available in plain or hot-dipped galvanized finish. This anchor requires the use of the 2/5-ton range ring clutch and the 2/3-ton load range recess plug. 

Plate-Lift L-Anchor  (ton x length)	Product  Code	Precast  Concrete  Panel  Thickness	Minimum Edge or Corner Distance	Shear Safe Working Load	Tension Safe Working Load	A	B	C	D
1-ton x 4" long	FL050	5" Min.	12"	2,000 lbs.	2,000 lbs.	1-1/4"	4"	1-7/16"	3/16"

Forged Foot Erection Anchor

· Ideal for horizontal to vertical edge lifts and the shear rotation of thin-walled units

· Specially designed head provides added protection against spalling

· Specially designed body allows for a full reinforcement

· Available in 2.5T, 5T, 10T capacities

· Based on a 4:1 safety factor

Superior Design Two steel protrusions or "ears" on the head of the anchor provide added protection against spalling. These ears hug either side of the ring clutch, restricting its rotation during lateral pulls. As a result, lateral forces are transmitted directly to the edges of the anchor instead of the concrete. The body of the Erection Anchor is shaped to allow full reinforcement for secure support and spall-free rotation.

Load Group	Axial Load	Code	Dimensions (Inch)
Tons	LBS		L	W	T
2.5	5500	GME2103-2.5	6-1-8	2	3/8
5.0	11000	GME2103-5.0	9-1/2	2-1/2	5/8
10.0	22000	GME2103-10.0	12	3-1/2	3/4